The Commodore Club of Tasmania Forums: Valkyrie666 - Viewing Profile

Hey All,
I'm deciding to clear out all my commodore gear and make way for a new smaller car.

I've got:
----------
VK Commodore wagon - In top order "no rust and dings" with raised rear king springs, new front and rear brakes. excellent electrics & salisbury 3.08 drum diff and EFI h-duty trimatic and tow kit. & also new 2-1/4" exhaust and 2 x mufflers. Will not come with motor as i'm selling seperate and interested parties will have to remove or buy motor with the car. just out of rego!. will come with paperwork if required. Looking for around $500

16" VS-SS mags - Full set of x 5 with brand spankin' new tread on 2. 90%+ on the other 3. Looking for around $600

2 x M76 5-speed gearboxes in need of overhaul. Looking for around $100

1 x VK factory M76 5-speed in VGO with brand new "never used" clutch kit, machined flywheel, gearbox mount, spigot bush, Pedal box with new rubbers, clutch cable & speedo gear + cable. Looking for around $600


Worked 3.3 black motor "only done 4,000Km's". 60thou bore-out, hyper pistons, crow 35666 cam, jp gears and high-vol pump, new isrealii bearings, new rods, decked block for zero clearance, reco'd 12-port head, brand new race curved distributor with all new coil and leads. wildcat extractors + lots more. can hear running. $$ spent. Looking for around $2K or with the running tripples $2800. Can Test!!!

Triple SU's with manifold + the lot. All ready to bolt on. Comes with throttle and linkage setup. Carbies are as new and have just been fully overhauled and tuned. These go great and i've spent around $1800 on them. May take around $1K for them or $2800 with motor.


Take the lot for around $4k.


If anyone wants to buy the mags, I will need a set of rollers that don't go flat for the wagon. I'm open to realistic offers, so PM me if you're interested and i'll get back to you!

Cheers!

Hey All

i'm looking for a manual pedal box for to suit a VK commodore. Also looking for a driveshaft to suit a holden VH to VK factory 5-speed. If you've got one for sale, PM me the price and location.

Would prefer to be able to get something from around hobart to southern tas area.

Cheers!

I am currently looking for either a driveshaft "preferably" or even a slip yoke for a M76 5-speed gearbox. These were factory for the VH/VK commodore series, and i've been also told they're the same as the XE/XF ford 5-speeds as well as the sigmas.

I'm also looking for a manual pedal box.

If you've got any of these bits laying around for sale MSG me here or send a PM.

Cheers!

For Sale Or Swap:

VN Commodore Series II Sedan.








The car is un-registered "will pit pass quite easily", but in excellent condition in and out, and I've put a lot of brand new gear into this car, including:

Professionally fitted Sony CD Player
Front & rear discs, pads, hand brake cable, drum shoes & wheel bearings - Installed by ABS Hobart
Professionally reconditioned steering rack, also with new boots and tie-rod ends
15" performance brand competition alloy mags with brand new Pirelli P6 tyre tread
New Front & rear nolathane bushes installed
Brand new factory sized exhaust with new chrome tip
Dark tinted windows
Brand new water pump, idler pulley & belt
+ lots more

Looking for around $1500 or will likely/prefer trade for an older holden with a 202 "prefer manual. WIll consider kingswood sedan, torana, or vb-vk commodore sedan or wagon. As i've just built a .60 thou 202 with a large cam/extractors & race carby. Looking for something with a good body to put it all into. I'd prefer any old holden six, manual, & doesn't have to be registered just in a good condition i.e. no major dents, steering/suspension issues/stuffed diff or trans. Not too worried about engine condition. Really would prefer trade.

PM or send me an email at: james.valkyrie@live.com.au

Cheers!

Up for sale is a redline roadmaster manifold for a 350 holley to suit a holden red 6

Price is $60

Can post at buyers expense, or collect from maydena.

Ph: 0448 290 265

Cheers